-26%

Produsent: RADIOLINK

Radiolink R6DSM 2.4G 10CH Mini Receiver SBUS/PWM

Specification:
 

Channels: 10 channels
Working voltage: 4.8-6V
Working current: 38-45mA (input voltage: 5V)
Size: 15*13 MM
Weight: 1g
Detachable antenna
4096 section precision, 0.25us per section, servo anti-shake rudder.
Control distance: about 600 meters, actually control distance depends on the environment.
Compatible transmitters: AT10II, AT10, AT9S Pro, AT9S and AT9
Veil. 390,- Ikke medlem: 290,-
290,-
  • Betal med faktura
  • Betal med kort
  • Delbetaling
  • Vipps
På lager På lager

SKU: RLR6DSM

  • Produktinformasjon
  • Brukermanual

R6DSM Overview:

DSSS&FHSS algorithm reduce overall signal interference for Radiolink R6DSM 2.4G rc receiver. Support PPM/SBUS signal output, high voltage servo(4.8-6v), works with Radiolink AT9/AT9S/AT9S Pro/AT10/AT10II.

 

Key Features:
 

1)Ultra light weight about 1 gram, esp for mini FPV racing quadcopter Drone
2)Support SBUS/PPM signal out put.
3)DSSS and FHSS spread spectrum woks synchronously, it provides excellent anti-interference performance, highly constant, and stable transmission.
4)Control Distance, The receiving distance can reach about 600 meters, and the actual control distance is related to the flight environment.
5)Works with Radiolink Models: AT9/ AT9S/ AT9S Pro/AT10/ AT10II transmitter
 

Note:  

R6DSM rc receiver suitable for Radiolink’s transmitter AT9/AT9S/AT9S Pro/AT10/AT10II

 

R6DSM Specification:
 

1) Channels: 10 channels
2) Working voltage: 4.8-6V
3) Working current: 38-45mA (input voltage: 5V)
4) Size: 15*13 MM
5) Weight: 1g
6) Detachable antenna
7) 4096 section precision, 0.25us per section, servo anti-shake rudder.
8) Control distance: about 600 meters, actually control distance depends on the environment.

 

How to bind to transmitter:
 

1. Place the transmitter and the receiver close to each other about 50cm.

2. Turn on the transmitter, then power on the R6DSM.

3. There is a black button on the R6DSM, press the binding button in one second until the receiver light starts blinking and release, after about 8 times blinking, match code success when receiver signal LED always on.


Working Mode:
 

Blue/purple LED, SBUS signal , 10 channels totally.

Red LED always, PPM signal, 10 channels totally.

 

Package Included:

R6DSM Receiver x 1

1

 

42

Easy to Bind and Change Signal
Only 1 second to bind with your radio, press twice bind button within 1 second to change signal mode. Blue LED -SBUS; Red LED-PPM

6

Modify System Menu

R6DSM+AT10II: SYSTEM Menu, Select CH-SELECT to 10CH mode.

R6DSM+AT9S: SYSTEM Menu, Select CH-SELECT to 10CH mode.

QQ图片20200710142833

Q:Why the LED of R6DSM is off after it’s powered on?

A:1. Check if the battery is charged.

2.Check if the polarity is correctly connected.

3.Check if the connection between the receivers and the power supply is good.

If there’s no problem with the above three points, the receiver may get burnt and needs to be repaired.

Q:Why the vehicle can’t be controlled after the binding between R6DSM and transmitter is done?

A:First, check if the power supply of the receiver and the transmitter is ok. Then modify the channel quantity of the transmitter (AT9/AT9S/AT10/AT10II) as 10 to work with R6DSM, the 10-channel receiver. Press Mode button to enter BASIC MENU => Rotate the dial to select SYSTEM and Enter => Set CH-SELECT as 10CH.

Q:When R6DSM works with AT9S, why the control range is more limited than 600 meters (in air) as advertised?

A:1.Check if the antenna of transmitter and receiver is damaged or welded joint

2.Check if there’s interference resources like electricity substation or high voltage cable or WIFI nearby.

3.Check the RSSI value.

A: Power on the transmitter and receiver with both antennas parallel and straight and within the distance of 30cm.

b: Then check the RSSI value. Range between 0~-30dBM is normal and if the value gets closer to 0, the signal is stronger.